Description

FT-MTRS-6E31-01is a high performance, cost effective modules, which is supporting Multi Rate 1.25-6.25Gbps, and transmission distance up to 10km on SM fiber. The transceiver consists of two sections: The transmitter section incorporates a 1310nm DFB Laser and a driver. The receiver section consists of a PIN photodiode integrated with a transimpedance preamplifier (TIA) and a Limitting Amplifier. The module is hot pluggable into the 20-pin connector. The high-speed electrical interface is base on low voltage logic, with nominal 100 Ohms differential impedance and AC coupled in the module.

 The optical output can be disabled by LVTTL logic high-level input of TX_DIS. Transmit Fault (Tx_Fault) is provided to indicate that the module transmitter has detected a fault condition related to laser operation or safety. Loss of signal (RX_LOS) output is provided to indicate the loss of an input optical signal of receiver. A serial EEPROM in the transceiver allows the user to access transceiver monitoring and configuration data via the 2-wire SFP Management Interface. This interface uses a single address, A0h, with a memory map divided into a lower and upper area. Basic digital diagnostic (DD) data is held in the lower area while specific data is held in a series of tables in the high memory area.

  Features

¡ñ  Up to 10KM transmission distance

¡ñ  Support  Multi Rate 1.25-6.25Gbps

¡ñ  1310nm DFB and PIN receiver

¡ñ  SFI electrical interface

¡ñ  2-wire interface for integrated Digital Diagnostic monitoring

¡ñ  SFP+ MSA package with duplex LC connector

¡ñ  Hot pluggable

¡ñ  Very low EMI and excellent ESD protection

¡ñ  +3.3V power supply

¡ñ  Power consumption less than 1W

¡ñ  Operating case temperature: -40~+85°C

Applications

¡ñ  High-speed storage area networks

¡ñ  Computer cluster cross-connect

¡ñ  Custom high-speed data pipes

¡ñ  LTE optical repeater application

Compliance

¡ñ  Compliant with Fiber Channel(FC)-Standard INCITS 352

¡ñ  Compliant with IEEE 802.3ae-2002

¡ñ  Compliant with FCC 47 CFR Part 15, Class B

¡ñ  Compliant with FDA 21 CFR 1040.10 and 1040.11, Class I except for deviations pursuant

  Specification

Notes:

[1] Average optical power shall be measured using the methods specified in TIA/EIA-455-95.

[2] Vertical eye closure penalty and stressed eye jitter are the test conditions for measuring stressed receiver sensitivity. They are not the required characteristic of the receiver.

Notes:

[1] Receiver sensitivity is informative. Stressed receiver sensitivity shall be measured with conformance test signal for BER =1x 10^-12 .

[2] Vertical eye closure penalty and stressed eye jitter are the test conditions for measuring stressed receiver sensitivity. They are not the required characteristic of the receiver.

Notes:

[1] Time from rising edge of TX Disable to when the optical output falls below 10% of nominal

[2] Time from falling edge of TX Disable to when the modulated optical output rises above 90% of nominal

[3] From power on or negation of TX Fault using TX Disable

[4] Time from fault to TX fault on

[5] Time TX Disable must be held high to reset TX_fault

[6] Time from LOS state to RX LOS assert

[7] Time from non-LOS state to RX LOS deassert.

[8] Time from rising or falling edge of Rate Select input until receiver bandwidth is in conformance with appropriate specification

Notes:

[1] For 1.25G data rate, the modules performance is compatible with 1G FC application but not fully compliant. If customer needs to fully compliant with 1.25G data rate specifications, we need to implement “Rate-Selection” function, please contact our sales team for detailed information.

Important Notice

Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice.

The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.