Description
FT-MTRS-02X13-Gis a high performance, cost effective modules, which is supporting Multi Rate 2.5-10.3125Gbps, and transmission distance up to 10km on SM fiber. The transceiver consists of two sections: The transmitter section incorporates a 1310nm DFB driver. The receiver section consists of a PIN photodiode integrated with a transimpedance preamplifier (TIA). The module is hot pluggable into the 20-pin connector. The high-speed electrical interface is base on low voltage logic, with nominal 100 Ohms differential impedance and AC coupled in the module.
The optical output can be disabled by LVTTL logic high-level input of TX_DIS. Transmit Fault (Tx_Fault) is provided to indicate that the module transmitter has detected a fault condition related to laser operation or safety. Loss of signal (RX_LOS) output is provided to indicate the loss of an input optical signal of receiver. A serial EEPROM in the transceiver allows the user to access transceiver monitoring and configuration data via the 2-wire SFP Management Interface. This interface uses a single address, A0h, with a memory map divided into a lower and upper area. Basic digital diagnostic (DD) data is held in the lower area while specific data is held in a series of tables in the high memory area.
Features
¡ñ Up to 10km transmission distance
¡ñ Support Multi Rate 2.5-10.3125Gbps
¡ñ 1310nm DFB and PIN receiver
¡ñ SFI electrical interface
¡ñ 2-wire interface for integrated Digital Diagnostic monitoring
¡ñ SFP MSA package with duplex LC connector
¡ñ Hot pluggable
¡ñ Very low EMI and excellent ESD protection
¡ñ +3.3V power supply
¡ñ Power consumption less than 1W
¡ñ Operating case temperature: 0~+70°C
Applications
¡ñ High-speed storage area networks
¡ñ Computer cluster cross-connect
¡ñ Custom high-speed data pipes
¡ñ LTE optical repeater application
Compliance
¡ñ Compliant with IEEE 802.3ae-2002
¡ñ Compliant with MSA SFF-8472
¡ñ Compliant with MSA SFF-8431
Specification
Absolute Maximum Ratings |
||||
Parameter |
Symbol |
Min. |
Max. |
Unit |
Storage Temperature |
TS |
-40 |
+85 |
¡æ |
Supply Voltage |
VCC3 |
0 |
3.6 |
V |
Relative Humidity |
RH |
5 |
+95 |
% |
RX Input Average Power |
Pmax |
- |
+3 |
dBm |
Recommended Operating Conditions
|
|||||
Parameter |
Symbol |
Min. |
Typical
|
Max. |
Unit |
Operating Case Temperature |
TC |
0 |
25 |
+70 |
¡æ |
Power Supply Voltage |
VCC3 |
3.13 |
3.3 |
3.47 |
V |
ICC3 |
- |
- |
300 |
mA |
|
Power Dissipation |
PD
|
- |
- |
1 |
W |
Data Rate |
|
2.5 |
|
10.3125 |
Gbps |
Transmission Distance |
|
- |
- |
10 |
Km |
Transmitter Operating Characteristic-Optical, Electrical |
||||||
Parameter |
Symbol |
Min. |
Typical |
Max. |
Unit |
Note |
Center Wavelength |
λC |
1260 |
1310 |
1355 |
nm |
Note1 |
Spectral Width£¨-20dB£© |
Pm |
- |
- |
1 |
nm |
|
Side Mode Suppression Ratio |
SMSR |
30 |
- |
- |
dBm |
|
Laser Off Power |
Poff |
- |
- |
-30 |
dBm |
|
Average Optical Power |
Pavg |
-8.2 |
- |
0.5 |
dBm |
Note1 |
Extinction Ratio |
ER |
3.5 |
- |
- |
dB |
|
Transmitter Dispersion Penalty |
TDP |
- |
- |
3.2 |
dB |
|
Relative Intensity Noise |
Rin |
- |
- |
-128 |
dB/Hz |
|
Optical Return Loss Tolerance |
|
12 |
- |
- |
dB |
|
Operating Data Rate |
|
2.5 |
|
10.3125 |
Gbps |
|
Optical Eye Mask |
Compliant with IEEE 802.3ae |
|
||||
Tx Input Diff. Voltage |
VI |
180 |
- |
700 |
mV |
|
Tx Fault |
VoL |
|
- |
0.4 |
V |
|
VoH |
2.4 |
|
Vcc |
V |
|
|
Tx Optical Power in OMA |
|
-5.2 |
|
|
dBm |
|
Notes:
[1] Average optical power shall be measured using the methods specified in TIA/EIA-455-95.
Receiver Operating Characteristic-Optical, Electrical |
||||||
Parameter |
Symbol |
Min. |
Typ. |
Max. |
Unit |
Note |
Center Wavelength |
λr |
1260 |
1310 |
1355 |
nm |
|
Receiver Sensitivity |
Psens |
- |
- |
-14.4 |
dBm |
Note1 |
Stressed Sensitivity (OMA) |
|
- |
- |
-12.6 |
dBm |
|
Los Assert |
LosA |
-30 |
- |
- |
dBm |
|
Los Dessert |
LosD |
- |
- |
-15 |
dBm |
|
Los Hysteresis |
LosH |
|
2 |
- |
dB |
|
Overload |
Pin |
0.5 |
- |
- |
dBm |
|
Receiver Reflectance |
|
- |
- |
-12 |
dB |
|
Operating Data Rate |
|
2.5 |
|
10.3125 |
Gbps |
|
Rx Output Diff Voltage |
Vo |
|
- |
850 |
mV |
|
Rx Output Rise and Fall Time |
Tr/Tf |
|
34 |
- |
ps |
20% to 80% |
Notes:
[1] Receiver sensitivity is informative. Stressed receiver sensitivity shall be measured with conformance test signal for BER =1x 10-12 .
Control and Status I/O Timing Characteristics |
||||||
Parameter |
Symbol |
Min. |
Max. |
Unit |
Note |
|
TX Disable Assert Time |
t_off |
- |
100 |
µs |
Note1 |
|
TX Disable Negate Time |
t_on |
- |
2 |
ms |
Note2 |
|
Time to initialize including reset of TX_Fault |
t_init |
- |
300 |
ms |
Note3 |
|
TX Fault Assert Time |
t_fault_on |
- |
1 |
ms |
Note4 |
|
TX Fault Reset Time |
t_reset |
10 |
- |
µs |
Note5 |
|
LOS Assert Time |
t_loss_on |
- |
100 |
µs |
Note6 |
|
LOS Deassert Time |
t_loss_off |
- |
100 |
µs |
Note7 |
|
Serial ID Clock Rate |
f_serial_clock |
- |
100 |
kHz |
|
|
TX Disable Assert Time |
t_off |
- |
100 |
µs |
Note1 |
|
|
|
|
|
|
|
|
Notes:
[1] Time from rising edge of TX Disable to when the optical output falls below 10% of nominal
[2] Time from falling edge of TX Disable to when the modulated optical output rises above 90% of nominal
[3] From power on or negation of TX Fault using TX Disable
[4] Time from fault to TX fault on
[5] Time from TX fault to TX nominal
[6] Time from LOS state to RX LOS assert
[7] Time from non-LOS state to RX LOS deassert.
Important Notice
Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice.
The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.