Description

FT-MTRS-1E31-01   is   a   high   performance,   cost effective modules, which is supporting Multi Rate4.9152Gbps to 10.3125Gbps, and transmission distance up to 10km on SM fiber. The transceiver consists of two sections: The transmitter section incorporates a laser driver and a 1310nm DFB laser. The receiver section consists of a PIN photodiode integrated with a transimpedance preamplifier (TIA) and a Limitting Amplifier. The module is hot pluggable into   the   20-pin   connector.   The   high-speed electrical interface is base on low voltage logic, with nominal 100 Ohms differential impedance and AC coupled in the module.

The optical  output can be disabled  byLVTTL logichigh-levelinputofTX_DIS.TransmitFault (Tx_Fault)isprovidedtoindicatethatthemodule transmitterhasdetectedafaultconditionrelatedto laseroperationorsafety.Lossofsignal(RX_LOS) outputisprovidedtoindicatethelossofaninput opticalsignalofreceiver.AserialEEPROMinthe transceiverallowstheusertoaccesstransceiver monitoringandconfigurationdataviathe2-wire SFPManagementInterface.Thisinterfaceusesa singleaddress,A0h,withamemorymapdivided into  a  lower  and  upper  area.  Basic  digital diagnostic(DD)dataisheldinthelowerarea while specificdataisheldinaseriesoftablesinthehigh memoryarea.

Features

¡ñ  Upto10kmtransmission distance

¡ñ  Support MultiRate 4.9152 Gbps to 10.3125 Gbps

¡ñ  1310nm DFB Laser Transmitter and PIN Receiver

¡ñ  SFIelectrical interface

¡ñ  2-wire interface for integratedDigital Diagnostic monitoring

¡ñ  SFP+MSApackagewith duplexLC connector

¡ñ  Hot pluggable

¡ñ  VerylowEMI and excellent ESD protection

¡ñ  +3.3V power supply

¡ñ  Power consumption less than1.0W

¡ñ  Operating casetemperature: -40~+85°C

Applications

¡ñ  High-speed storage area networks

¡ñ  Computer clustercross-connect

¡ñ  Custom high-speed data pipes

¡ñ  LTE optical repeater application

Compliance

¡ñ  CompliantwithFiber Channel(FC)-Standard INCITS352

¡ñ  CompliantwithIEEE 802.3ae-2002

¡ñ  Compliantwith SFF-8431

Specification

Notes:

[1]  Non-condensing state

Notes:

 [1]Eye Mask Margin(1000 consecutive snapshots at typical rate and room temperature)

Notes:

 [1]Time from rising edge ofTXDisable towhen theoptical output fallsbelow10% of nominal

 [2] Time from falling edge of TX Disable to when the modulated optical output rises above 90% of nominal

 [3] From power on or negation of TX Fault using TX Disable

 [4] Time from fault to TX fault on

 [5] Time TX Disable must be held high to reset TX_fault

 [6] Time from LOS state to RX LOS assert

 [7] Time from non-LOS state to RX LOS deassert.

Important Notice

Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice.

The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.