±ê×¼¹âÄ£¿é
EPON ONU STICK SFP
Specifications
- ²úÆ·ÐͺÅ: GEPON ONU¹âÄ£¿é
- ¼æÈÝÆ·ÅÆ: ȫϵÁÐ
- ·â×°ÀàÐÍ: SFF/SFP
- ´«ÊäËÙÂÊ: 1.25T/1.25R
- ´«Êä¾àÀë: 20KM
- ·¢É䲨³¤: 1310T/1490R
- ½ÓÊÕ²¨³¤: 1310T/1490R
- ÊÂÇéζÈ: ÉÌÒµ¼¶0¡æ¡«+70¡æ/¹¤Òµ¼¶-40¡æ¡«+85¡æ ¿ÉÑ¡
- Êý×ÖÕï¶Ï: ´øDDM
- ½ÓÊÕÁéÃô¶È: 20KM
- ½ÓÊÕÁéÃô¶È: 20KM
Description
FEATURES
- Single fiber bi-directional data links symmetric 1.25Gbps EPON ONU application with EPON MAC function.
- SC/UPC receptacle SFP with EPON ONU MAC inside, ¡°Plug-and-play¡± via auto-discovery and configuration
- 1310nm FP burst mode transmitter, 1490nm PIN-TIA continuous mode receiver
- 0 to 70¡ãC operating case temperature for EONU-STICK-20, C-Temp;
-40 to 85¡ãC operating case temperature for EONU-STICK-20I, I -Temp;
- Single 3.3V power supply
- Digital diagnostic monitor interface compatible with SFF-8472
- SFP MSA compliance
- Low EMI and excellent ESD protection
- Class I laser safety standard IEC-60825 compliant
- RoHS-6 compliance
APPLICATIONS
- Ethernet Passive Optical Networks(EPON)
- EONU-STICK-20 / EONU-STICK-20I is an MSA-compliant SFP that incorporates not just the optics for an ONU, but all of the electronics need as well. It is a ¡°PON on a Stick¡± that an entire FTTH ONU in a slightly oversized SFP. It can be plugged into networking equipment. Allowing the data interfaces on a switch, router, PBX, etc. to be customized for different fiber environments and distance requirements
STANDARDS
- Complies with SFP Multi-Source Agreement (MSA) SFF-8074i
- Complies with IEEE 802.3ah-2004 1000BASE-PX20 EPON ONU
- Highly flexible 802.1Q VALN support
- 802.1p/q support
- Complies with SFF 8472
- Complies with FCC 47 CFR Part 15, Class B
- Complies with FDA 21 CFR 1040.10 and 1040.11
|
ABSOLUTE MAXIMUM RATING |
|||||
|
Parameter |
Symbol |
Min. |
Max. |
Unit |
Notes |
|
Storage Ambient Temperature |
TSTG |
-40 |
85 |
¡ãC |
|
|
Operating Case Temperature |
Tc |
0 |
70 |
¡ãC |
EONU-STICK-20 |
|
Tc |
-40 |
85 |
¡ãC |
EONU-STICK-20I |
|
|
Operating Humidity |
OH |
5 |
95 |
% |
|
|
Power Supply Voltage |
VCC |
-0.5 |
3.6 |
V |
|
|
RECOMMENDED OPERATING CONDITION |
||||||
|
Parameter |
Symbol |
Min. |
Typ. |
Max. |
Unit |
Notes |
|
Power Supply Voltage |
VCC |
3.13 |
3.3 |
3.47 |
V |
|
|
Power Dissipation |
PD |
1.85 |
2.10 |
2.42 |
W |
Max value under High temp environment |
|
Operating Case Temperature |
Tc |
0 |
+70 |
¡ãC |
EONU-STICK-20 |
|
|
Tc |
-40 |
+85 |
¡ãC |
EONU-STICK-20I |
||
|
Operating Humidity Range |
OH |
5 |
95 |
% |
||
|
Data Rate |
1.25 |
Gbit/s |
||||
|
Data Rate Drift |
-100 |
+100 |
PPM |
|||
|
TRANSMITTER OPTICAL CHARACTERISTICS |
|||||||
|
Parameter |
Symbol |
Min. |
Typ. |
Max. |
Unit |
Note |
|
|
Optical Center Wavelength |
¦ËC |
1260 |
1310 |
1360 |
nm |
||
|
Spectral Width (-20dB) |
?¦Ë |
2.8 |
nm |
||||
|
Average Launch Optical Power |
AOP |
0 |
4 |
dBm |
Launched into SMF Fiber |
||
|
Burst off Average Output Power |
-45 |
dBm |
|||||
|
Extinction Ratio |
ER |
9 |
dB |
||||
|
Rise/Fall Time (20%-80%) |
TR/TF |
0.26 |
ns |
||||
|
RIN15OMA |
-115 |
dB/Hz |
|||||
|
Optical Return Loss Tolerance |
15 |
dB |
|||||
|
Transmitter Reflectance |
-10 |
dB |
|||||
|
Transmitter and Dispersion Penalty |
TDP |
2 |
dB |
Transmit on 20km SMF. |
|||
|
Optical Waveform Diagram |
IEEE Std 802.3ahTM-2004 |
PRBS 27-1 @1.25bps |
|||||
TRANSMITTER ELECTRICAL CHARACTERISTICS |
||||||
|
Parameter |
Symbol |
Min. |
Typ. |
Max. |
Unit |
Notes |
|
Data Input Differential Swing |
300 |
1800 |
mV |
CML input, AC coupled |
||
|
Input Differential Impedance |
90 |
100 |
110 |
¦¸ |
||
|
Transmitter TxDisable Control Voltage - Low |
0 |
0.8 |
V |
|||
|
Transmitter TxDisable Voltage - High |
2.0 |
VCC |
V |
|||
|
Transmitter Fault Alarm Voltage - Low |
0 |
0.4 |
V |
|||
|
Transmitter Fault Alarm Voltage ¨C High |
2.4 |
Vcc |
V |
|||
RECEIVER OPTICAL CHARACTERISTICS |
||||||
|
Parameter |
Symbol |
Min. |
Typ. |
Max. |
Unit |
Notes |
Operating Wavelength
|
¦Ëc |
1480 |
1490 |
1500 |
nm |
|
|
Sensitivity |
SEN |
-27 |
dBm |
PRBS 27 -1 @1.25Gbps BER¡Ü10E-12, ER=9dB EOL, Over Temperature |
||
|
Saturation Optical Power |
SAT |
-3 |
dBm |
|||
|
Loss of Signal De-Assert |
LOSD |
-29 |
dBm |
|||
|
Loss of Signal Assert |
LOSA |
-39 |
dBm |
|||
|
Signal-Detected Hysteresis |
0.5 |
6 |
dBm |
|||
|
Receiver Reflectance |
-12 |
dB |
¦Ë=1490nm |
|||
|
WDM Filter Isolation |
38 |
dB |
¦Ë=1550nm |
|||
|
35 |
dB |
¦Ë=1650nm |
||||
|
RECEIVER ELECTRIAL CHARACTERISTICS |
||||||
|
Parameter |
Symbol |
Min. |
Typ. |
Max. |
Unit |
Notes |
|
Data Output Differential Swing |
300 |
1200 |
mV |
CML output, AC coupled |
||
|
Loss of Signal - Low |
0 |
0.4 |
V |
|||
|
Loss of Signal - High |
2.4 |
VCC |
V |
|||
Figure 1 SFP Transceiver Electrical Pad Layout
|
PIN DESCRIPTION |
|||
|
PIN |
Name |
Description |
Notes |
|
1 |
VeeT |
Transmitter Ground |
Note5 |
|
2 |
TX Fault |
Transmitter Fault Indication |
Note 1 |
|
3 |
TX Disable |
Transmitter Disable |
Note 2, Module disables on high or open |
|
4 |
MOD-DEF2 |
Module Definition 2 |
Note 3, wire serial ID Interface |
|
5 |
MOD-DEF1 |
Module Definition 1 |
Note 3, wire serial ID Interface |
|
6 |
MOD-DEF0 |
Module Definition 0 |
Note 3, Grounded in Module |
|
7 |
Rate |
Not connected |
None |
|
8 |
LOS |
Loss of Signal |
Note 4 |
|
9 |
VeeR |
Receiver Ground |
Note 5 |
|
10 |
VeeR |
Receiver Ground |
Note 5 |
|
11 |
VeeR |
Receiver Ground |
Note 5 |
|
12 |
RD- |
Inv. Received Data Out |
Note 6 |
|
13 |
RD+ |
Received Data Out |
Note 6 |
|
14 |
VeeR |
Receiver Ground |
Note 5 |
|
15 |
VccR |
Receiver Power |
3.3 ¡À5%, Note 7 |
|
16 |
VccT |
Transmitter Power |
3.3 ¡À5%, Note 7 |
|
17 |
VeeT |
Transmitter Ground |
Note 5 |
|
18 |
TD+ |
Transmit Data In |
Note 8 |
|
19 |
TD- |
Inv.Transmit Data In |
Note 8 |
|
20 |
VeeT |
Transmitter Ground |
Note 5 |
- TX Fault is an open collector/drain output, which should be pulled up with a 4.7K ¨C 10K¦¸ resistor on the host board. Pull up voltage between 2.0V and VccT, R+0.3V. When high, output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.
- TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7 ¨C 10K¦¸ resistor. Its states are:
Low (0 ¨C 0.8V): Transmitter on
(>0.8, < 2.0V): Undefined
High (2.0 ¨C 3.465V): Transmitter Disabled
Open: Transmitter Disabled
- Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7K ¨C 10K¦¸ resistor on the hostThe pull-up voltage shall be VccT or VccR.
Mod-Def 0 is grounded by the module to indicate that the module is present
Mod-Def 1 is the clock line of two wire serial interface for serial ID
Mod-Def 2 is the data line of two wire serial interface for serial ID
- LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with a 4.7K ¨C 10K¦¸ resistor. Pull up voltage between 2.0V and VccT, R+0.3V. When high, this output indicates the received optical power is below the worst-case receiver sensitivity (as defined by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.
- VeeR and VeeT may be internally connected within the SFP module.
- RD-/+: These are the differential receiver outputs. They are AC coupled 100 ¦¸ differential lines which should be terminated with 100 ¦¸ (differential) at the user SERDES. The AC coupling is done inside the module and is thus not required on the host board. The voltage swing on these lines will be between 370 and 2000 mV differential (185 ¨C 1000 mV single ended) when properly terminated.
- VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.3V ¡À5% at the SFP connector pin. Maximum supply current is 300 mA. Recommended host board power supply filtering is shown below. Inductors with DC resistance of less than 1¦¸=should be used in order to maintain the required voltage at the SFP input pin with 3.3V supply voltage. When the recommended supply filtering network is used, hot plugging of the SFP transceiver module will result in an inrush current of no more than 30 mA greater than the steady state value. VccR and VccT may be internally connected within the SFP transceiver module.
- TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100¦¸ differential termination inside the module. The AC coupling is done inside the module and is thus not required on the host board. The inputs will accept differential swings of 300 ¨C 1800 mV (150 ¨C 900 mV single-ended), though it is recommended that values between 500 and 1200 mV differential (250 ¨C 600 mV single-ended) be used for best EMI performance. 500 and 1600 mV differential (250 ¨C 800 mV single-ended) be used for best EMI performance
|
DESCRIPTION OF EEPROM ADDRESS A0H AND A2H |
SFP ONU uses the two wire serial bus to access two blocks of 256-byte EEPROM address 1010000X (A0h) and 1010001X (A2h) ,
A0h stores static information including product and vendor IDs and A2h provides diagnostic information about the module¡¯s present operating conditions. The transceiver generates this diagnostic data by digitization of internal analog signals. Calibration and alarm/warning threshold data is written during device manufacture.
The figure below shows the detail descriptions of A0h and A2h. All of information is accessible by a local host equipment, and can be retrieved by OLT remotely through EPON OAM messages.
Figure 4Detail descriptions of A0h and A2h defined by SFF-8472
|
EEPROM INFORMATION (A0h) |
||||
|
Data Address |
Field Size (Byte) |
Name Of filed |
Hex |
Coded value |
|
0(00) |
1 |
Identifier |
03 |
SFP |
|
1(01) |
1 |
Ext .Identifier |
04 |
GBIC/SFP function is defined by serial ID only |
|
2(02) |
1 |
Connector |
01 |
SC |
|
3(03) |
8 |
Transceiver (Note 3) |
00 |
1000BASE-PX |
|
4(04) |
00 |
|||
|
5(05) |
00 |
|||
|
6(06) |
80 |
|||
|
7(07) |
00 |
|||
|
8(08) |
00 |
|||
|
9(09) |
00 |
|||
|
10(0A) |
00 |
|||
|
11(0B) |
1 |
Encoding |
01 |
8B10B |
|
12(0C) |
1 |
BR, Nominal |
0D |
1.25GHz |
|
13(0D) |
1 |
Reserved |
00 |
|
|
14(0E) |
1 |
Length (9um) |
14 |
20(km) |
|
15(0F) |
1 |
Length (9um) |
C8 |
200(100m) |
|
16(10) |
1 |
Length (50um) |
00 |
|
|
17(11) |
1 |
Length (62.5um) |
00 |
|
|
18(12) |
1 |
Length (Copper) |
00 |
|
|
19(13) |
1 |
Reserved |
00 |
|
|
20(14) |
16 |
Vendor name |
53 |
S |
|
21(15) |
55 |
U |
||
|
22(16) |
50 |
P |
||
|
23(17) |
45 |
E |
||
|
24(18) |
52 |
R |
||
|
25(19) |
58 |
X |
||
|
26(1A) |
4F |
O |
||
|
27(1B) |
4E |
N |
||
|
28(1C) |
20 |
<space> |
||
|
29(1D) |
4C |
L |
||
|
30(1E) |
54 |
T |
||
|
31(1F) |
44 |
D |
||
|
32(20) |
2E |
. |
||
|
33(21) |
20 |
<space> |
||
|
34(22) |
20 |
<space> |
||
|
35(23) |
20 |
<space> |
||
|
36(24) |
1 |
Reserved |
00 |
|
|
37(25) |
3 |
Vendor OUI |
00 |
|
|
38(26) |
00 |
|||
|
39(27) |
00 |
|||
|
40(28) |
16 |
Vendor PN (Note3) |
53 |
S |
|
41(29) |
4F |
O |
||
|
42(2A) |
45 |
E |
||
|
43(2B) |
42 |
B |
||
|
44(2C) |
33 |
3 |
||
|
45(2D) |
34 |
4 |
||
|
46(2E) |
36 |
6 |
||
|
47(2F) |
36 |
6 |
||
|
48(30) |
2D |
- |
||
|
49(31) |
50 |
P |
||
|
50(32) |
53 |
S |
||
|
51(33) |
47 |
G |
||
|
52(34) |
4D |
M |
||
|
53(35) |
20 |
<space> |
||
|
54(36) |
20 |
<space> |
||
|
55(37) |
20 |
<space> |
||
|
56(38) |
4 |
Vendor rev (Note3) |
31 |
1 |
|
57(39) |
30 |
0 |
||
|
58(3A) |
20 |
<space> |
||
|
59(3B) |
20 |
<space> |
||
|
60(3C) |
2 |
Wavelength |
05 |
1310nm |
|
61(3D) |
1E |
|||
|
62(3E) |
1 |
Reserved |
00 |
|
|
63(3F) |
1 |
CC_BASE |
xx |
Note1 |
|
64(40) |
2 |
Options |
00 |
TX_FAULT, LOS |
|
65(41) |
0A |
|||
|
66(42) |
1 |
BR, max |
00 |
|
|
67(43) |
1 |
BR, min |
00 |
|
|
68(44) |
16 |
Vendor SN (Note3) |
xx |
|
|
69(45) |
xx |
|||
|
70(46) |
xx |
|||
|
71(47) |
xx |
|||
|
72(48) |
xx |
|||
|
73(49) |
xx |
|||
|
74(4A) |
xx |
|||
|
75(4B) |
xx |
|||
|
76(4C) |
xx |
|||
|
77(4D) |
xx |
|||
|
78(4E) |
xx |
|||
|
79(4F) |
xx |
|||
|
80(50) |
xx |
|||
|
81(51) |
xx |
|||
|
82(52) |
xx |
|||
|
83(53) |
xx |
|||
|
84(54) |
8 |
Date code (Note3) |
xx |
Year |
|
85(55) |
xx |
Year |
||
|
86(56) |
xx |
Month |
||
|
87(57) |
xx |
Month |
||
|
88(58) |
xx |
Day |
||
|
89(59) |
xx |
Day |
||
|
90(5A) |
20 |
<Space> |
||
|
91(5B) |
20 |
<Space> |
||
|
92(5C) |
1 |
Diagnostic |
68 |
DD Implemented; Internally Calibrated; Average Power |
|
93(5D) |
1 |
Enhanced Options |
B0 |
Optional Alarm/warning Flags Implemented; TX_FAULT; RX_LOS; |
|
94(5E) |
1 |
SFF-8472 Compliance |
02 |
Rev 9.5of SFF-8472. |
|
95(5F) |
1 |
CC_EXT |
xx |
Note 2 |
|
Digital Diagnostic Specification (A2h) |
|||
|
Data Address |
Parameter |
Range |
Range |
|
96(60) |
Temperature |
-40 to 85¡ãC |
¡À3¡ãC |
|
97(61) |
|||
|
98(62) |
Vcc Voltage |
3.0 to 3.6V |
¡À3¡ãC |
|
99(63) |
|||
|
100(64) |
Bias Current |
0 to 130 mA |
¡À10% |
|
101(65) |
|||
|
102(66) |
TX Power |
-1 to 5 dBm |
¡À3dB |
|
103(67) |
|||
|
104(68) |
RX Power |
-28 to -2 dBm |
¡À3dB |
|
105(69) |
|||
|
ORDERING INFORMATION |
|
Part Number |
Product Description |
|
EONU-STICK-20 / |
EPON ONU STICK SFP (MAC Inside),0?C ~ +70?C |
|
EONU-STICK-20I |
EPON ONU STICK SFP (MAC Inside), -40 to +85¡ãC |
Related Products
EPON-SFP-OLT¹âÄ£¿é
ÇкÏIEEE802.3ahÒªÇó
Âú×ãµçÐÅÒªÇóPX20+/PX20++
¾ßÓÐÇкÏSFF-8472¹æ·¶µÄDDM¹¦Ð§
¹âÏ˽ӿÚÊǵ¥ÏËSC/LC½Ó¿Ú»òÕß´øβÏË
·¢Éä¶Ë1490nm³¤·¢¹â¡¢1310nmDFPÍ»·¢Ä£Ê½¼¤¹âÆ÷
½ÓÊÕ1310nm¡¢1490nmµÄPIN/APD¼¤¹âÆ÷
ÇкÏROSH6µÄ±ê×¼
GPON-SFP-OLT¹âÄ£¿é
- Single fiber bi-directional data links asymmetric TX 2488Mbps / RX1244Mbps application
- 1490nm continuous-mode DFB laser transmitter and 1310nm burst-mode APD-TIA receiver
- Small Form Factor Pluggable package with SC/UPC Connector
- Support Class C+ 17~32dB attenuation range application (With FEC)
- Reset burst-mode receiver design support more than 15dB dynamic range
- 0 to 70¡ãC operating temperature
- Single 3.3V power supply
- Digital diagnostic monitoring interface
- Digital burst RSSI function to monitor the input optical power level
- LVPECL compatible data input/output interface
- LVTTL transmitter disable control
- LVTTL transmitter laser fault alarm
- LVTTL receiver Signal Detect (SD) indication response within 50ns.
- Low EMI and excellent ESD protection
- Class I laser safety standard IEC-60825 compliant
- RoHS-6 compliance
10GEPON-XFP-OLT¹âÄ£¿é
- Single fiber bi-directional data links TX 10.3125Gbps/ Burst Mode RX10.3125Gbps application
- Single fiber bi-directional data links TX 10.3125Gbps/ Burst Mode RX1.25Gbps application
- Single fiber bi-directional data links TX 1.25Gbps/ Burst Mode RX1.25Gbps application
- 0 to 70¡ãC operating case temperature
- 3.3V,5V power supply
- XFP package with SC Receptacle connector
- Hot-pluggable capability
- High power 1577nm EML DFB LD
- High power 1490nm DFB LD
- High sensitivity 1270nm and 1310nm APD
- Support 20km transmission distance with SMF
- Low EMI and excellent ESD protection
- Digital diagnostic monitor interface
- RoHS compliance for FTCX-OLXG-XX
10GEPON ONU¹âÄ£¿é
- Single fiber bi-directional data links 1.25G TX/10.3125G RX or 10.3125G TX/10.3125G RX
- 0¡ãC to 70¡ãC operating case temperature
- Single 3.3V power supply
- SFP+ package with SC Receptacle connector
- Hot-pluggable capability
- High power 1310nm DFB LD and high sensitivity APD
- Support 20km transmission distance with SMF
- CML compatible data input/output interface
- Low power dissipation
- Low EMI and excellent ESD protection
- Digital diagnostic monitor interface
- RoHS-6 compliance for FTCS-ONXE-XXX
XGPON-ONU¹âÄ£¿é
- Single fiber bi-directional data links Asymmetric TX 2.488Gbps/RX9.953Gbps application
- 0 to 70¡ãC operating case temperature
- Single 3.3V power supply
- Power dissipation<1.5W
- SFP+ package with SC Receptacle connector
- Hot-pluggable capability
- High power 1270nm DML DFB LD and high sensitivity 1577nm APD
- Support 20km transmission distance with SMF
- CML compatible data input/output interface
- Low power dissipation
- Low EMI and excellent ESD protection
- Digital diagnostic monitor interface
- RoHS-6 compliance
GPON-ONU¹âÄ£¿é
- Single fiber bi-directional data links with asymmetric 1244Mbps upstream and 2488Mbps downstream
- 1310nm DFB burst mode transmitter
- 1490nm APD-TIA continuous mode receiver
- High power 1550nm video signal rejection
- 0 to 70¡ãC operating case temperature for C-temp class, and -40 to 85¡ãC operating case temperature for I-temp class,
- 2¡Á10 SFF or SFP package with SC/APC or SC/UPC pigtail connector
- Single 3.3V power supply
- LVPECL compatible data input interface
- CML compatible data output interface
- LVTTL burst enable control
- LVTTL receiver signal-detected indication
- TX_SD function
- Digital diagnostic monitor interface compatible with SFF-8472
- Low EMI and excellent ESD protection
- Class I laser safety standard IEC-60825 compliant
- RoHS-6 compliance