标准光�？�
155M 15km(商温) SFP Transceiver
Description
Description
The FT-MXPD-033S transceiver is a high performance, cost effective module that supports data-rate up to 155Mbps.
The transmitter section and the receiver section work independently in the transceiver. The receiver section contains an InGaAs PIN photo diode, a transimpedance amplifier and a post amplifier (with working data rate up to 155Mbps), functionally transmit received optical power to steady electrical data.
This transceiver meets the Small Form Pluggable (SFP) industry standard package utilizing an integral LC-Duplex optical interface connector. An enhanced Digital Diagnostic Monitoring Interface compliant with SFF-8472 has been incorporated into the transceiver. It allows real time access to the transceiver operating parameters such as transceiver temperature, laser bias current, transmitted optical power,received optical power and transceiver supply voltage by reading a built-in memory with I2Cinterface.
Features
● Operating data rate 155Mbps
● Industry standard Small Form Pluggable (SFP) package
● Digital diagnostic monitor interface compliant with SFF-8472
● Duplex LC connector
● Single +3.3V power supply
● Differential LVPECL inputs and outputs
● TTL signal detect indicator
● Hot-pluggable capability
● RoHS compliant
Applications
● SDH STM-1/SONET OC-3
● Fast Ethernet
● Other optical links
Compliance
● SFP MSA
● SFF-8472
● ITU-T G.957/GR-253
● ROHS
Specification
|
Absolute Maximum Ratings |
||||||
|
Parameter |
Symbol |
Min |
Typical |
Max |
Unit |
Notes |
|
Storage Temperature |
TSTG |
-40 |
- |
85 |
ºC |
|
|
Operating Relative Humidity |
RH |
5 |
- |
95 |
% |
|
|
Supply Voltage |
VCC |
-0.5 |
- |
3.7 |
V |
|
|
Power Dissipation |
PD |
|
|
1 |
W |
@70 ºC,3.5V |
|
Recommended Operating Conditions |
||||||
|
Parameter |
Symbol |
Min |
Typical |
Max |
Unit |
Notes |
|
Ambient temperature |
Ta |
0 |
- |
70 |
℃ |
Note1 |
|
Supply Voltage |
VCC |
3.135 |
3.3 |
3.465 |
V |
|
|
Data Rate |
|
- |
155 |
- |
Mbps |
|
Notes:
[1] Commercial Temperature:0℃~ +70 ℃.
|
Transmitter Operating Characteristic-Optical ，Electrical |
||||||
|
Parameter |
Symbol |
Min |
Typical |
Max |
Units |
Notes |
|
Differential Input Voltage |
Vin p-p |
500 |
- |
2400 |
mV |
|
|
Output Optical Power |
PO |
-14 |
- |
-8 |
dBm |
BOL |
|
-15 |
- |
-8 |
dBm |
EOL |
||
|
Extinction Ratio |
ER |
8.5 |
- |
|
dB |
|
|
Center Wavelength Range |
λc |
1261 |
1310 |
1360 |
nm |
|
|
Spectral Width |
Δλ |
- |
- |
7.7 |
nm |
FP (RMS) |
|
Output Optical Eye |
Complies with ITU-T G.957 eye masks when filtered |
|||||
|
Tx_Disable Voltage |
VOH |
2.0 |
- |
Vcc |
V |
LVTTL |
|
VOL |
0 |
- |
0.8 |
V |
LVTTL |
|
|
Tx_Fault Voltage |
VOH |
2.0 |
- |
Vcc |
V |
LVTTL |
|
VOL |
0 |
- |
0.8 |
V |
LVTTL |
|
|
Receiver Operating Characteristic-Optical ，Electrical |
||||||
|
Parameter |
Symbol |
Min |
Typical |
Max |
Units |
Notes |
|
Differential Output Voltage |
Vout p-p |
370 |
|
2000 |
mV |
50Ω load to Vcc-2V |
|
Receiver Sensitivity |
Sen |
|
|
-31 |
dBm |
BOL,[1] |
|
|
|
-28 |
dBm |
EOL,[1] |
||
|
Overload Input Power |
So |
-8 |
|
|
dBm |
|
|
Los of Signal Voltage |
VOH |
2.0 |
|
Vcc |
V |
LVTTL |
|
VOL |
0 |
|
0.8 |
V |
LVTTL |
|
|
Los Asserted |
PA |
-45 |
|
|
dBm |
|
|
Los De-asserted |
PD |
|
|
-31.5 |
dBm |
|
|
Los Hysteresis |
PD- PA |
0.5 |
|
|
dB |
|
|
Receiver Optical Wavelength |
λIN |
1260 |
|
1620 |
nm |
|
Notes:
[1] Measured with a PRBS223-1 test pattern@155Mb/s, ER=9dB, BER=10-10.
|
Reliability Test Definitions and Distributions |
|||||
|
Group |
Test |
Reference |
Condition |
SS[1] |
C[2] |
|
Mechanical Integrity |
Mechanical shock |
MIL-STD-883 Method 2002.3 |
5 times/axis, 1500G, 0.5ms |
11 |
0 |
|
Vibration |
MIL-STD-883 Method 2007.2 |
20G, 20~2000Hz, 4min/cys,4cys/axis |
11 |
0 |
|
|
Thermal Shock |
MIL-STD-883 Method 1011 |
△T=100c 00C-1000C |
11 |
0 |
|
|
Endurance |
Accelerated Aging |
GR-468-CORE |
85℃, 2000 hrs |
25 |
- |
|
High temperature Storage |
GR-468-CORE |
85℃, 2000 hrs |
11 |
0 |
|
|
Low temperature Storage |
GR-468-CORE |
-40℃, 72 hrs |
11 |
0 |
|
|
Temperature Cycles |
MIL-STD-883 Method 1010.7 GR-468-CORE |
-40℃~85℃ 500 cycles |
11 |
0 |
|
|
Damp Heat |
MIL-STD-202 Method 103 GR-468-CORE |
85 ℃, 85%RH 1000 hrs |
11 |
0 |
|
|
Cyclic moisture resistance |
MIL-STD-883 Method 1004.7 GR-468-CORE |
20 cycles |
11 |
0 |
|
|
Special Test |
ESD threshold |
MIL-STD-883E Method 3015.7 |
2000V HBM |
6 |
0 |
Note: [1] SS: Sample Size; [2] C: Maximum number of failure allowed in the test.
Important Notice
Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice.
The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.
Related Products
1000BASE-T Copper SFP Transceiver
1000BASE-T Copper SFP Transceiver
F-tone Networks 1000BASE-T copper SFP transceiver is based on the SFP Multi-Source Agreement (MSA). They are compatible with the Gigabit Ethernet and 1000BASE-T standards as specified in IEEE Std 802.3, which support 1000Mbps data-rate up to 100 meter reach over unshielded twisted-pair category-5 cable.
1.25G 40km(商温)SFP Transceiver
1.25G 40km(商温)SFP Transceiver
The transmitter section and the receiver section work independently in the transceiver. The receiver section contains an InGaAs PIN photo diode, a transimpedance amplifier and a post amplifier (with working data rate up to 1250Mbps), functionally transmit received optical power to steady electrical data.
1.25G 15KM(工温)SFP Transceiver
1.25G 15KM(工温)SFP Transceiver
The transmitter section and the receiver section work independently in the transceiver. The receiver section contains an InGaAs PIN photo diode, a transimpedance amplifier and a post amplifier (with working data rate up to 1250Mbps), functionally transmit received optical power to steady electrical data.
2.5G 2km(工温) SFP Transceiver
2.5G 2km(工温) SFP Transceiver
The transmitter section and the receiver section work independently in the transceiver. The receiver section contains an InGaAs PIN photo diode, a transimpedance amplifier and a post amplifier (with working data rate up to 2.5Gbps), functionally transmit received optical power to steady electrical data.
2.5G 15km(工温) SFP Transceiver
2.5G 15km(工温) SFP Transceiver
The transmitter section and the receiver section work independently in the transceiver. The receiver section contains an InGaAs PIN photo diode, a transimpedance amplifier and a post amplifier (with working data rate up to 2.5Gbps), functionally transmit received optical power to steady electrical data.