25Gb/s SFP28 CWDM 40km ¹âÄ£¿é

Description
      F-tone Networks¡¯FTCS-C3325G-40Dxx 25Gb/s SFP28 transceiver consists of five sections: the LD driver, the limiting amplifier, the digital diagnostic monitor, the CWDM DFB laser and the APD photo-detector. The module data link up to 20km in 9/125um single mode fiber.
The module optical connection is duplex LC and shall be compatible with SFP+ 28Gbps and backward compatible with legacy 10G SFP+ pluggable. The SFP28 CWDM LR module is a dual directional device with a transmitter and receiver plus a control management interface (2-wire interface) in the same physical package. 2-wire interface is used for serial ID, digital diagnostics and module control function.
      The transmitter converts 25Gbit/s serial PECL or CML electrical data into serial optical data compliant with the 25GBASE-LR standard. An open collector compatible Transmit Disable (TxDis) is provided. Logic ¡°1¡± or no connection on this pin will disable the laser from transmitting. Logic ¡°0¡± on this pin provides normal operation. The transmitter has an internal automatic power control loop (APC) to ensure constant optical power output across supply voltage and temperature variations. An open collector compatible Transmit Fault (TxFault) is provided. TXFault is module output contact that when high, indicates that the module transmitter has detected a fault condition related to laser operation or safety. The TXFault output contact is an open drain/collector and shall be pulled up to the VccHost in the host with a resistor in the range 4.7-10 k¦¸. TXDisable is a module input contact. When TX_Disable is asserted high or left open, the SFP28 module transmitter output shall be turned off. This contact shall be pulled up to VccT with a 4.7 k¦¸ to 10 k¦¸ resistor
      The receiver converts 25Gbit/s serial optical data into serial PECL/CML electrical data. An open collector compatible Loss of Signal is provided. RxLOS when high indicates an optical signal level below that specified in the relevant standard. The RxLOS contact is an open drain/collector output and shall be pulled up to VccHost in the host with a resistor in the range 4.7-10 k¦¸, or with an active termination. Power supply filtering is recommended for both the transmitter and receiver. The RxLOS signal is intended as a preliminary indication to the system in which the SFP28 is installed that the received signal strength is below the specified range. Such an indication typically points to non-installed cables, broken cables, or a disabled, failing or a powered off transmitter at the far end of the cable.

Features
¡ñ Up to 25.78Gb/s data links
¡ñ CWDM DFB laser and APD receiver
¡ñ Up to 40km on 9/125um SMF
¡ñ Hot-pluggable SFP footprint
¡ñ Support Digital Monitoring interface
¡ñ Class 1 laser safety certified
¡ñ Cost effective SFP28 solution, enables higher port densities and greater bandwidth
¡ñ RoHS-10 compliant and lead-free
¡ñ Single +3.3V power supply
¡ñ 2-wire interface for management specifications compliant with SFF-8472 digital diagnostic monitoring interface for optical transceivers
¡ñ All-metal housing for superior EMI performance
¡ñ Case operating temperature
        Commercial: 0 ~ +70¡æ
        Extended: -10 ~ +80¡æ
        Industrial: -40 ~ +85¡æ

Applications
¡ñ High-speed storage area networks
¡ñ Computer cluster cross-connect
¡ñ Custom high-speed data pipes
¡ñ Inter Rack Connection

Mechanical Dimensions
Ordering Information

´ó±¦ÓéÀÖ | F-tone Networks

ÆóÒµÓÊÏ䣺sales@f-tone.com
ÆóÒµÍøÕ¾£ºwww.f-tone.com
ÆóÒµÍøÕ¾£ºwww.sfpgmk.com
ÆóÒµµç»°£º028-85255257
ÆóÒµ´«Õ棺028-85977702

×¢£º±¾²úÆ·ÓÐÈ«¹ú²ú»¯ÐͺſÉÑ¡
±¾²úƷΪSFP CWDMϵÁйâÄ£¿é£¬ÈçÓÐÐèÒª£¬ÇëÁªÏµ´ó±¦ÓéÀÖ¡£