±ê×¼¹âÄ£¿é
10Gbps SFP+ 80KMµ¥Ä£¹âÄ£¿é
Specifications
- ²úÆ·ÐͺÅ: FTCS-151X-80X
- ¼æÈÝÆ·ÅÆ: ȫϵÁÐ
- ·â×°ÀàÐÍ: SFP+
- ´«ÊäËÙÂÊ: Supports 9.95Gbps to 10.5Gbps bit rates
- ´«Êä¾àÀë: ´«Êä¾àÀë80KM
- ·¢É䲨³¤: 1550nm
- ½ÓÊÕ²¨³¤: 1550nm
- ÊÂÇéζÈ: ÉÌÒµ¼¶0¡æ¡«+70¡æ/¹¤Òµ¼¶-40¡æ¡«+85¡æ ¿ÉÑ¡
- Êý×ÖÕï¶Ï: ´øDDM
- ½ÓÊÕÁéÃô¶È: ´«Êä¾àÀë80KM
- ½ÓÊÕÁéÃô¶È: ´«Êä¾àÀë80KM
Description
10Gbps SFP+ 80KM Optical Transceiver
F-tone 80KM SFP+ ZR Optical Transceiver
Features
- Compliant with SFF-8431 and IEE802.3ae
- Data rate selectable ¡Ü4.25Gbps or 9.95Gbps to 11.3Gbps bit rates
- Cooled EML transmitter and APD receiver
- link length up to 80km
- Low Power Dissipation 1.4W Typical (Maximum:2W)
- Operating Case Temperature:0¡ãC to 70¡ãC(Standard), -40¡ãC to 85¡ãC (Industrial)
- Single 3.3V power supply
- Diagnostic Performance Monitoring of module temperature, supplyVoltages, laser bias current, transmit optical power, receive optical power
- RoHS compliant and lead free
Applications
- 10G Ethernet
- 10G Fiber Channel (with/without FEC)
Description
- F-tone SFP+ZR Transceiver is designed for 8.5G/10G Fiber- Channel and 10GBE applications. The transceiver consists of two sections: The transmitter section incorporates a colded EML laser. And the receiver section consists of a APD photodiode integrated with a TIA. All modules satisfy class I laser safety requirements. F-tone SFP+ZR Digital diagnostics functions are available via a 2-wire serial interface, as specified in SFF-8472, which allows real-time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage.
Absolute Maximum Ratings
|
Parameter |
Symbol |
Min |
Max |
Unit |
|
Supply Voltage |
Vcc |
-0.5 |
3.8 |
V |
|
Storage Temperature |
Tst |
-40 |
85 |
?C |
|
Relative Humidity |
Rh |
0 |
85 |
% |
Operating Conditions
|
Parameter |
Symbol |
Min |
Typical |
Max |
Unit |
|
Supply Voltage |
Vcc |
3.13 |
3.3 |
3.47 |
V |
|
Supply current [1] |
Icc |
420 |
610 |
mA |
|
|
Operating Case temperature |
Tca |
-5 |
- |
70 |
?C |
|
Module Power Dissipation [2] |
Pm |
- |
1.4 |
2 |
W |
Notes:
[1] Supply current is shared between VCCTX and VCCRX. Typical Supply current test at 25¡æ£¬Max Supply current test at 60~70¡æ
[2] In-rush is defined as current level above steady state current requirements
Transmitter Specifications ¨C Optical
|
Parameter |
Symbol |
Min |
Typical |
Max |
Unit |
|
Center Wavelength |
lc |
1528 |
1565 |
nm |
|
|
Optical Average Power |
Po |
0 |
- |
+4 |
dBm |
|
Side Mode Suppression Ratio |
SMSR |
30 |
- |
- |
dB |
|
Optical Transmit Power (disabled) |
PTX_DISABLE |
- |
- |
-30 |
dBm |
|
Extinction Ratio |
ER |
9 |
- |
dB |
|
|
RIN21OMA |
-128 |
dB/Hz |
|||
|
Optical Return Loss Tolerance |
21 |
dB |
|||
|
Dispersion penalty(1600ps/nm) |
DP |
2 |
dB |
Transmitter Specifications ¨C Electrical
|
Parameter |
Symbol |
Min |
Typical |
Max |
Unit |
|
Data Rate |
Mra |
- |
10.3 |
11.3 |
Gbps |
|
Input differential impedance |
Rim |
- |
100 |
- |
¦¸ |
|
Differential data Input |
VtxDIFF |
120 |
- |
850 |
mV |
|
Transmit Disable Voltage |
VD |
2.0 |
- |
Vcc3+0.3 |
V |
|
Transmit Enable Voltage |
Ven |
0 |
- |
+0.8 |
V |
|
Transmit Disable Assert Time |
Vn |
- |
- |
100 |
us |
Receiver Specifications ¨C Optical
|
Parameter |
Symbol |
Min |
Typical |
Max |
Unit |
|
Input Operating Wavelength |
¦Ë |
1110 |
- |
1650 |
nm |
|
Receiver sensitivity [1] |
- |
- |
-24 |
dBm |
|
|
Maximum Input Power |
RX-overload |
- |
- |
-8 |
dBm |
|
Loss of Signal Asserted |
-34 |
- |
- |
dBm |
|
|
LOS De-Asserted |
- |
- |
-24 |
dBm |
|
|
LOS Hysteresis |
0.5 |
- |
- |
dB |
Notes:
[1] Measured with conformance test signal for BER = 10¨C12. PRBS31, Data Rate=10.3Gbps.
Receiver Specifications ¨C Electrical
|
Parameter |
Symbol |
Min |
Typical |
Max |
Unit |
|
Data Rate |
Mra |
- |
10.3 |
11.3 |
Gbps |
|
Differential Output Swing |
Vout P-P |
350 |
- |
850 |
mV |
|
Rise/Fall Time |
Tr / Tf |
24 |
- |
- |
ps |
|
Loss of Signal ¨CAsserted |
VOH |
2 |
- |
Vcc3+0.3- |
V |
|
Loss of Signal ¨CNegated |
VOL |
0 |
- |
+0.4 |
V |
Figure1.Electrical Pin-out Details
Pin Descriptions
|
Pin |
Symbol |
Name/Description |
|
1 |
VEET [1] |
Transmitter Ground |
|
2 |
Tx_FAULT [2] |
Transmitter Fault |
|
3 |
Tx_DIS [3] |
Transmitter Disable. Laser output disabled on high or open |
|
4 |
SDA [2] |
2-wire Serial Interface Data Line |
|
5 |
SCL [2] |
2-wire Serial Interface Clock Line |
|
6 |
MOD_ABS [4] |
Module Absent. Grounded within the module |
|
7 |
RS0 [5] |
RS0 for Rate Select: Open or Low = Module supports ¡Ü4.25Gbps High = Module supports 9.95 Gb/s to 10.3125 Gb/s |
|
8 |
RX_LOS [2] |
Loss of Signal indication. Logic 0 indicates normal operation |
|
9 |
RS1 [5] |
No connection required |
|
10 |
VEER [1] |
Receiver Ground |
|
11 |
VEER [1] |
Receiver Ground |
|
12 |
RD- |
Receiver Inverted DATA out. AC Coupled |
|
13 |
RD+ |
Receiver DATA out. AC Coupled |
|
14 |
VEER [1] |
Receiver Ground |
|
15 |
VCCR |
Receiver Power Supply |
|
16 |
VCCT |
Transmitter Power Supply |
|
17 |
VEET [1] |
Transmitter Ground |
|
18 |
TD+ |
Transmitter DATA in. AC Coupled |
|
19 |
TD- |
Transmitter Inverted DATA in. AC Coupled |
|
20 |
VEET [1] |
Transmitter Ground |
Notes:
[1] Module circuit ground is isolated from module chassis ground within the module.
[2].should be pulled up with 4.7k ¨C 10k ohms on host board to a voltage between 3.15Vand 3.6V.
[3]Tx_Disable is an input contact with a 4.7 k¦¸ to 10 k¦¸ pullup to VccT inside the module.
[4]Mod_ABS is connected to VeeT or VeeR in the SFP+ module. The host may pull this contact up to Vcc_Host with a resistor in the range 4.7 k¦¸ to10 k¦¸.Mod_ABS is asserted ¡°High¡± when the SFP+ module is physically absent from a host slot.
[5]RS0 and RS1 are module inputs and are pulled low to VeeT with > 30 k¦¸ resistors in the module.
Ordering information
|
Part Number |
Product Description |
|
FTCS-151X-80 |
10Gbps, 1550nm SFP+ 80km, 0?C ~ +70?C |
| FTCS-151X-80I | 10Gbps, 1550nm SFP+ 80km,-40¡ãC to 85¡ãC (Industrial) |
Related Products
XFP-850¶àÄ£¹âÄ£¿é
Supports 9.95Gbps to 10.5Gbps bit rates
Maximum link length of 300m (50um,MMF,2000MHz.Km)
850nm VCSEL laser and PIN receiver
Low power consumption <1.5W
+3.3V +1.8Vpower supply
XFP MSA package with duplex LC connector
XFI electrical interface
No reference clock required
Compatible with RoHS
Excelllent EMI performance
Built-in digital diagnostic functions
Temperature range: 0¡æ to +70¡æ
High reliability
XFP-10KM¹âÄ£¿é
Supports 9.95Gb/s to 11.1Gb/s bit rates
Hot-pluggable XFP footprint
Maximum link length of 10km with SMF
1310nm Uncooled DFB laser
XFP MSA package with duplex LC connector
No reference clock required
Compatible with RoHS
+3.3V +1.8V power supply
Power dissipation <2.5W
Built-in digital diagnostic functions
Operating temperature: 0¡ãC to 70¡ãC(Standard), -40¡ãC to 85¡ãC (Industrial)
XFP-40KM ¹âÄ£¿é
Features
Supports 10GBE Application at the Data-Rate of 9.953Gbps to 10.3125Gbps
Maximum link length of 40km with SMF
1550nm cooled EML laser and PIN photodiode
XFP MSA package with duplex LC connector
XFI High Speed Electrical Interface
+5V, +3.3V,+1.8V power supply
Low Power Dissipation 3.5W Maximum
2-wire interface for management and diagnostic monitor
Compatible with RoHS
Compatible with IEEE 802.3ae 10 Gigabit Ethernet
Compatible with Sonet OC-192/SDH STM-64
SFP+ 850nm¶àÄ£¹âÄ£¿é
- Hot-pluggable SFP+ footprint
- Supports rate selectable 1.25 Gb/sOr 9.95 to 10.3 Gb/s bit rates
- Power dissipation < 1W
- RoHS-6 compliant ( lead-free )
- Single 3.3V power supply
- Maximum link length of 300m on2000 MHZ-km MMF
- Uncooled 850nm VCSEL laser
- Receiver limiting electrical interface
- Duplex LC Connector
- Built-in digital diagnostic functions
- Commercial temperature range£º 0¡ãC to 70¡ãC(Standard), -40¡ãC to 85¡ãC (Industrial)
10Gbps SFP+ 10KMµ¥Ä£¹âÄ£¿é
- Optical interface compliant to IEEE 802.3ae 10GBASE-LR
- Electrical interface compliant to SFF-8431
- Hot Pluggable
- 1310nm DFB transmitter, PIN photo-detector
- Operating case temperature: 0¡ãC to 70¡ãC(Standard), -40¡ãC to 85¡ãC (Industrial)
- Low power consumption
- Applicable for 10km SMF connection
- All-metal housing for superior EMI performance
- Advanced firmware allow customer system encryption information to be stored in transceiver
- Cost effective SFP+ solution, enables higher port densities and greater bandwidth
10Gbps SFP+ 40KMµ¥Ä£¹âÄ£¿é
- Compliant with SFF-8431 and IEE802.3ae
- Data rate selectable ¡Ü4.25Gbps or 9.95Gbps to 10.3Gbps bit rates
- Cooled EML transmitter and PIN receiver
- link length up to 40km
- Low Power Dissipation 1.5W Maximum
- Operating Case Temperature£º0¡ãC to 70¡ãC(Standard), -40¡ãC to 85¡ãC (Industrial)
- Single 3.3V power supply
- Diagnostic Performance Monitoring of module temperature, supplyVoltages, laser bias current, transmit optical power, receive optical power
- RoHS compliant and lead free