²ôîï¹âÏË·Å´óÆ÷H1
²úÆ·½éÉÜ
Features
1. The OLAH is a fiber amplifier and power supply integrated in a 1RU&2RU shelf. Multiple output ports can be chose.
2. The OLAH incorporates electrical control circuitry wit a digital signal processor and includes photodiodes for monitoring the optical input and output power through tap couplers.
3. Double cooling system can protect the pump laser to work in a long time.
4. RJ45 and RS 232 port, SNMP management system.
5. Good stability, VFD displays the working conditions, good trouble alarm system.
Technical Parameters
Model |
-20-27 |
-28 |
-29 |
-30 |
-31 |
-32 |
-33 |
-34 |
-35 |
-36~38 |
Output Power (dBm) |
20-27 |
28 |
29 |
30 |
31 |
32 |
33 |
34 |
35 |
36~38 |
CATV Input power (dBm) |
-3¡«10 |
|||||||||
CATV Wavelength Range (nm) |
1530¡«1565 |
|||||||||
Output port |
8¡¢16¡¢32¡¢64 |
|||||||||
Output power stability (dB) |
<±0.2 |
|||||||||
C/N (dB) |
≥45 |
|||||||||
CSO (dB) |
≥63 |
|||||||||
CTB (dB) |
≥63 |
|||||||||
Bias oscillation sensitivity (dB£© |
<0.2 |
|||||||||
Bias oscillation dispersion£¨PS£© |
<0.5 |
|||||||||
Optical return loss £¨dB£© |
≥45 |
|||||||||
CATV Fiber connector |
FC/APC¡¢SC/APC |
|||||||||
Noise ratio £¨dB£© |
<5.0(0dBm optical input) |
|||||||||
connector |
RJ45(SNMP) ¡¢RS232 |
|||||||||
Power loss £¨W£© |
≤130 |
|||||||||
Working Voltage £¨V£© |
220V(90¡«265)¡¢DC-48V |
|||||||||
Working Temp £¨¡æ£© |
-20¡«85 |
|||||||||
size £¨mm£© |
540(L)×486(W)×88(H) |
Important Notes
1. Please avoid eyes directly to output.
2. Please turn off the power first then plug in or out the patch cord
3. EDFA has very small influence on CSO and CTB, but has big influence in C/N. The input optical power influence the C/N. High optical input gets higher C/N. Please see the following data. The minimum optical input should be 4dBm.
C/N and Optical Input
Optical In£¨dBm£© |
7 |
6 |
5 |
4 |
3 |
2 |
1 |
0 |
-1 |
-2 |
-3 |
C/N£¨dBm£© |
52.4 |
52.2 |
52.0 |
51.6 |
51.1 |
50.6 |
50.1 |
49.5 |
48.8 |
48.1 |
47.3 |
Normal Trouble Solution
The display in screen of the EDFA shows the correct output of the pump laser, if the output is lower than showed,
please check as the following steps.
1. Check the optical meter. Because of the high out of EDFA, please don’t use Chinese optical meter to test the EDFA, the advised one is EXFO.
2. The output adaptor burnt.
3. The operator plug in and out the patch cord when the power on, this will burnt the output pigtail connector and make the output lower. The solution is to splice a new the pigtail connector.
4. Some operators use the bad quality patch cord and its fiber core is too long, after connected, it will hurts the pigtail of pump laser output. In this condition, in the first test, the output is correct, but in the second time, the output become lower. The solution is also to splice a new pigtail connector.
5. The wavelength of the input deviates far from 1550nm, it will make both the output port and screen show lower.
6. Too low input will make both the output and screen show lower.
Precautions:
1. Before installation or operation of unit, please carefully go through the user’s manual.
2. OLAH Series EDFA should be serviced only by qualified personnel.
3. Before proceeding with installation and/or operation of transmitter, please assure that transmitter is well earthed.
4. OLAH series EDFA are Class III laser products. Use of controls, adjustments, and procedures other than those specified herein may result in hazardous laser radiation exposure.
Warranty Term
OLAH Series EDFA are covered by Two YEARs Limited Warranty, which starts from the initial date of your purchase.We provide its customer whole-life technical supports. If warranty is expired, repair service only charges parts (if required). In the event that a unit must be returned for service, before returning the unit, please be advised that:
1. Warranty mark pasted on the housing of unit must be in good conditions.
2. A clear and readable material describes model number, serial number and troubles should be offered.
3. Please pack the unit in its original container. If the original container is no longer available, please pack the unit in at least 3 inches of shock absorbing material.
4. Returned unit(s) must be prepaid and insured. COD and freight collect can not be acceptable.
NOTE: we do not assume responsibility for damage caused by improper packing of returned unit(s).
The following situation is not covered by warranty:
1. The unit fails to perform because of operators’ faults.
2. Warranty mark is modified, damaged and/or removed.
3. Damage caused by Force Majeure.
4. The unit has been unauthorized alteration and/or repaired.
5. Other troubles caused by operators’ faults.
Important Notice